ib technology
Micro RWD MF (Mifare) LP (low-power) specification
The MicroRWD MF (Mifare) LOW-POWER version is a complete read/write system for
13.56 MHz Mifare 1k, 4k and Ultralight cards. The module is pin-compatible and virtually
identical in operation and features to the “standard” version (NOTE differences in EEPROM
parameters and the three polling rates).
However the LOW-POWER version uses a different specification microcontroller offering
lower voltage operation and is designed to be powered from four alkaline battery cells.
During the Polling Delay period the microcontroller enters SLEEP mode with the RF device
in hard power-down mode to reduce the current consumption to a very low level.
The module wakes up after the polling delay period and the process repeats. The RWD-
MIFARE “low-power” Windows applications can be used to configure the parameters and
read/write data.
Parameter
Supply Voltage (performance optimised for 5 volt operation)
Operating temperature
AVERAGE current consumption. (1 second polling)
Active period for RF AND host communication (each
polling cycle).
Peak antenna voltage (optimum tuning)
Peak antenna current (optimum tuning) for short period each
polling cycle (up to 10 mS burst)
Polling Delay (SLEEP / Power-down mode)
Current consumption during Polling delay / SLEEP
Current consumption during RF ON each polling cycle
Maximum data rate (between card and RWD)
Range (dependent on antenna dimensions and tuning)
Auxiliary output drives
Serial Interface
Serial Communication Parameters
Typical Value
4 – 6 volts DC (operation
from 4 x alkaline cells)
-40 deg C to + 85 deg C
Less than 150 μ A
Up to 20 mS
30 volts peak-to-peak
150 mA
4 mS to 8 seconds
Less than 20 μ A
Less than 20mA
106k baud
25-50 mm
Up to 25mA
TTL level RS232
9600 baud, 8 data bits, no
parity, 1 stop bit protocol
with CTS handshake
Basic electrical specification with LEDs pins and auxiliary outputs NOT connected.
Note that the MicroRWD MF (Mifare) LOW-POWER version is designed for optimum
performance and range at 5-volt operation. Performance will be reduced at maximum and
minimum operating voltage.
During the “Polling Delay” SLEEP/Power-down period the logic levels on the RWD pins
remain active and so for minimum current consumption, the LEDs and the auxiliary output
drives must be disconnected (and the Beep output delay set to zero).
33
相关PDF资料
RWD-QT MODULE RCVR RFID QUAD TAG
RXD-433-KH2 RECEIVER/DECODER 433MHZ KH2 SER
RXM-418-LC-S RECEIVER RF 418MHZ SMT
RXM-418-LR_ RECEIVER 418MHZ LR SERIES
RXM-869-ES_ RECEIVER RF 869MHZ 16PIN SMD
RXM-GPS-SG-T GPS MODULE SMD SIRF
RXM-GPS-SR-T GPS MODULE SMD SIRF W/ANT
RZE002P02TL MOSFET P-CH 20V 200MA EMT3
相关代理商/技术参数
RWD-MIFARE-OEM 功能描述:MOD RCVR RFID MIFARE W/ANTENNA RoHS:是 类别:RF/IF 和 RFID >> RFID IC 系列:MIFARE® 其它有关文件:CR14 View All Specifications 标准包装:1 系列:- RF 型:收发器 频率:13.56MHz 特点:ISO14443-B 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SO 包装:Digi-Reel® 其它名称:497-5719-6
RWD-QT 功能描述:MODULE RCVR RFID QUAD TAG RoHS:是 类别:RF/IF 和 RFID >> RFID 读取模块 系列:- 产品目录绘图:DLP-RFID-UHF1B 标准包装:1 系列:- RF 型:读/写 频率:900MHz 特点:ISO 18000-6 a/b/c 封装/外壳:模块 供应商设备封装:模块 包装:散装 产品目录页面:635 (CN2011-ZH PDF) 其它名称:813-1029
RWDU500-WCCV4 制造商:Pass & Seymour/Legrand 功能描述:WALL OCC/VAC SENSOR/DIMMER 3W 500W
RWE182M550DEN2S 制造商:United Chemi-Con 功能描述:CGD550X218E N12F2D
RWE222M450C1N2S 制造商:United Chemi-Con 功能描述:CGC450X222L N12F1A
RWE350LG332M50X130LL 功能描述:铝质电解电容器-螺旋式接线端 3300UF 350V RoHS:否 制造商:Cornell Dubilier 电容:2400 uF 容差:- 10 %, + 50 % 电压额定值:450 V ESR:38 mOhms 工作温度范围:- 40 C to + 85 C 系列:CGS 直径:76 mm (3 in) 长度:143 mm (5.625 in) 引线间隔:31.75 mm (1.25 in) 产品:Computer Grade Electrolytic Capacitors